![]() |
|
Post Reply ![]() |
Page <1234 8> |
Author | ||
Drew540i ![]() Really Senior Member II ![]() ![]() Available from all good newsagents! Joined: 15-August-2005 Location: The Mansfield Massive Status: Offline Points: 632 |
![]() |
|
Hmmmm............
I had a problem recently with a 1992 520i - okay so it's rather more modern than an old E24, but...... Basically, it would not start. No power to the ECU even though the ECU was fine. Turns out that the E32 and E34 have a fusible link in the battery plus cable that powers up the engine managment loom. And it blows. ![]() My money would be on removing all the underdash trim and the lower cowling from the steering column and inspecting all the wiring from the ignition barrel. If it's had an immobiliser, chances are some Dick used a Scotchlok (the mark of a bodger) to connect up an immobiliser or alarm. It's such a common problem on old cars. The DME relay also affects the fuel pump. Are the plugs wet with fuel? Even if the fuel rail is primed and the pump working, the injectors still need to be opened. In short, is there fuel there and on the plugs? If it's simply an ignition fault, they should stink of petrol. The coil needs 12 volts (battery voltage - about 12-13v) at terminal 15. Use a test light between Terminal 15 and battery MINUS (ground). If there's nothing there, run a fused wire between battery plus and terminal 15. It should then run, and the problem will be in the wiring between the coil and ignition switch. Could even be the control unit for the OBC which is ignition related for the OBC anti theft function. |
||
![]() |
||
Sponsored Links | ||
![]() |
||
phb10186 ![]() Really Senior Member I ![]() ![]() Joined: 18-April-2005 Location: North London Status: Offline Points: 331 |
![]() |
|
My red ECU is fine!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Peter (hiyyaboy) let me test it, which I am indebted for - thanks again mate. But this eliminates only one more thing. -ben |
||
![]() ![]() 1985 635 CSI with Style 134's 1998 Z3 2.8i |
||
![]() |
||
Horsetan ![]() Really Senior Member II ![]() ![]() Say Neigh to Gatsos Joined: 11-April-2003 Location: Please let it be Ireland Status: Offline Points: 6381 |
![]() |
|
You should've seen the spaghetti that Ben removed......
No smell at all. |
||
![]() ![]() |
||
![]() |
||
phb10186 ![]() Really Senior Member I ![]() ![]() Joined: 18-April-2005 Location: North London Status: Offline Points: 331 |
![]() |
|
There is a stink of petrol, fuel is OK Its like going 1 step forward and 2 steps back! |
||
![]() ![]() 1985 635 CSI with Style 134's 1998 Z3 2.8i |
||
![]() |
||
Horsetan ![]() Really Senior Member II ![]() ![]() Say Neigh to Gatsos Joined: 11-April-2003 Location: Please let it be Ireland Status: Offline Points: 6381 |
![]() |
|
There wasn't when you tried to start it in front of me the other week! |
||
![]() ![]() |
||
![]() |
||
phb10186 ![]() Really Senior Member I ![]() ![]() Joined: 18-April-2005 Location: North London Status: Offline Points: 331 |
![]() |
|
There is definately a stink of fuel from the cylinders after its been turned over for a while |
||
![]() ![]() 1985 635 CSI with Style 134's 1998 Z3 2.8i |
||
![]() |
||
Horsetan ![]() Really Senior Member II ![]() ![]() Say Neigh to Gatsos Joined: 11-April-2003 Location: Please let it be Ireland Status: Offline Points: 6381 |
![]() |
|
OK so, the fuel has come through One less glitch to worry about |
||
![]() ![]() |
||
![]() |
||
phb10186 ![]() Really Senior Member I ![]() ![]() Joined: 18-April-2005 Location: North London Status: Offline Points: 331 |
![]() |
|
Car turns over again.... Battery was flat!!! Its still in the same state as it has been for thye last 11 weeks, Relays, fuel, fuses, sensors, ECU's all OK I think Im looking for an earth fault, a dodgy connection or an unplugged wire somewhere, but its not going to be easy to find. Peter gave me part number '65811373726' so im going to try that box out. Its something to do with the OBC and its a smallish black box under the glovebox, with the 2 green 4 wired plugs going in to it. |
||
![]() ![]() 1985 635 CSI with Style 134's 1998 Z3 2.8i |
||
![]() |
||
Drew540i ![]() Really Senior Member II ![]() ![]() Available from all good newsagents! Joined: 15-August-2005 Location: The Mansfield Massive Status: Offline Points: 632 |
![]() |
|
So, you've tested the coil for a 12v supply then??
Until you do this, you're just wasting your time. |
||
![]() |
||
Drew21 ![]() Groupie ![]() Joined: 14-October-2005 Status: Offline Points: 51 |
![]() |
|
seconded if its defo an ignition problem and its a non-starter my money is on the LT supply side of the coil/ ECU/ whatever electrics the ignition system needs. I might also hedge my bets on a faulty king lead (ie the HT lead from the coil to the distributor) |
||
![]() |
||
Drew540i ![]() Really Senior Member II ![]() ![]() Available from all good newsagents! Joined: 15-August-2005 Location: The Mansfield Massive Status: Offline Points: 632 |
![]() |
|
Absolutely. If there is voltage at the coil, the thing to
try would be to pull the king lead out of the distributor cap, stick a spark plug in the end, rest it on the engine and see if it sparks. Also, Motronic systems really do need a fully charged battery with a good 13 volts to spin the motor over AND give a spark. If it gives a spark here but not at the plug leads, suspect the rotor arm/cap. But firstly, test terminal 15 (it's marked clearly) on the coil for 12v. If there's nothing there, run a lead to battery + to power it up. If it's a problem caused by dodgy ignition/alarm wiring, it should start and run. Make this the first thing you do tomorrow, after giving the battery a good charge. |
||
![]() |
||
phb10186 ![]() Really Senior Member I ![]() ![]() Joined: 18-April-2005 Location: North London Status: Offline Points: 331 |
![]() |
|
no spark from king lead
|
||
![]() ![]() 1985 635 CSI with Style 134's 1998 Z3 2.8i |
||
![]() |
||
phb10186 ![]() Really Senior Member I ![]() ![]() Joined: 18-April-2005 Location: North London Status: Offline Points: 331 |
![]() |
|
ill test the coil and LT side of things tomorrow, and jump it from terminal 15 that was suggested. I take it that terminal 15 is in the fuse box then, or is it on the coil? |
||
![]() ![]() 1985 635 CSI with Style 134's 1998 Z3 2.8i |
||
![]() |
||
phb10186 ![]() Really Senior Member I ![]() ![]() Joined: 18-April-2005 Location: North London Status: Offline Points: 331 |
![]() |
|
Can you start the car with the instrument cluster removed??? I did take it out a while back, and was wondering of a problem could lie there, and Im just thinking about it in advance in case the tests that everyone has suggested turn out negative. Basically could there be one connection to the cluster thats somehow come adrift, that would cause a non-start??? |
||
![]() ![]() 1985 635 CSI with Style 134's 1998 Z3 2.8i |
||
![]() |
||
phb10186 ![]() Really Senior Member I ![]() ![]() Joined: 18-April-2005 Location: North London Status: Offline Points: 331 |
![]() |
|
OK tested some stuff... Coil is dead, and not getting any voltage. Fuse 15 in the fuse box has no voltage when connected to the battery. Engine and the rest of the car has good earth. Is fuse 15 definately the one that links through to the LT side of the ignition, because: http://www.stormpages.com/countchocula1/bmw/etm102.htm & http://www.stormpages.com/countchocula1/bmw/etm102a.htm suggests that fuse 15 is not used! I want to be sure before I start looking. so still no start, but I know that the coill is dead on the LT side Edited by phb10186 |
||
![]() ![]() 1985 635 CSI with Style 134's 1998 Z3 2.8i |
||
![]() |
||
Horsetan ![]() Really Senior Member II ![]() ![]() Say Neigh to Gatsos Joined: 11-April-2003 Location: Please let it be Ireland Status: Offline Points: 6381 |
![]() |
|
That diagram you're looking at was aimed at the US-spec 635s. Now, what does your authentic instruction book (which Dave swapped with you) say about fuse number 15??? |
||
![]() ![]() |
||
![]() |
||
phb10186 ![]() Really Senior Member I ![]() ![]() Joined: 18-April-2005 Location: North London Status: Offline Points: 331 |
![]() |
|
ill check it out in a sec
|
||
![]() ![]() 1985 635 CSI with Style 134's 1998 Z3 2.8i |
||
![]() |
||
phb10186 ![]() Really Senior Member I ![]() ![]() Joined: 18-April-2005 Location: North London Status: Offline Points: 331 |
![]() |
|
OK, some ammedments.... Seems as if the coil is getting 12 volts after all! No spark from king lead, but I have changed the king for another, and still no spark. I must admit that I did check the distrubutor cap and rotor arm, and they seemed fine. I have also taken the ignution swith out and cleaned it, and its the same as it was before. But if the car is turning over and there is 12 volts to the coil, but nothing after, it suggests an HT problem. so ill have to check this out now i suppose, unless someone else has any other suggestions. |
||
![]() ![]() 1985 635 CSI with Style 134's 1998 Z3 2.8i |
||
![]() |
||
Horsetan ![]() Really Senior Member II ![]() ![]() Say Neigh to Gatsos Joined: 11-April-2003 Location: Please let it be Ireland Status: Offline Points: 6381 |
![]() |
|
It would be highly amusing if you got the car running by the time I came round |
||
![]() ![]() |
||
![]() |
||
phb10186 ![]() Really Senior Member I ![]() ![]() Joined: 18-April-2005 Location: North London Status: Offline Points: 331 |
![]() |
|
Im feeling like a complete knacker here!!!!
|
||
![]() ![]() 1985 635 CSI with Style 134's 1998 Z3 2.8i |
||
![]() |
Post Reply ![]() |
Page <1234 8> |
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |