Bavarian-Board.co.uk - BMW Owners Discussion Forum Homepage
Forum Home Forum Home > Technical & Model Specific Forums > General Motors
  New Posts New Posts RSS Feed - 2-pack paint question
  FAQ FAQ  Forum Search   Register Register  Login Login

Forum Locked2-pack paint question

 Post Reply Post Reply
Author
Message
Kevin_E30_318iS View Drop Down
Really Senior Member II
Really Senior Member II
Avatar

Joined: 14-December-2002
Location: Ireland
Status: Offline
Points: 883
Direct Link To This Post Topic: 2-pack paint question
    Posted: 08-August-2003 at 09:35
Does anyone know if 2 pack paints and hardeners are compatible between different manufacturers, e.g. Glasurit paint and Lesonal hardner?

Thanks,
Kevin_1990_318iS
Back to Top
Sponsored Links


Back to Top
steveo View Drop Down
Newbie
Newbie


Joined: 22-December-2002
Location: United Kingdom
Status: Offline
Points: 9
Direct Link To This Post Posted: 08-August-2003 at 19:52
hi.
i am a paint sprayer for a large merc maindealer using glasurit paint. If it were me i would stick to the same brand hardener as you have different types such as, hs (high solid) & ms (medium solid), & whilst you may get away with using different hardener you may have problems with curing, drop in gloss, polishing & application. If you are stuck & you have to use it i suggest you spray a test panel first (old panel or sheet of metal) & see what result you get.
Hope this helps.

steve.
Back to Top
Kevin_E30_318iS View Drop Down
Really Senior Member II
Really Senior Member II
Avatar

Joined: 14-December-2002
Location: Ireland
Status: Offline
Points: 883
Direct Link To This Post Posted: 08-August-2003 at 23:03
Thanks for the feedback. I use the 2-pack for touching up stone chips and small rust spots with a small brush as it gives a good result and can be sanded and polished to blend in.
My main concern was that they wouldn't mix at all and I'd be at the loss of the tin of hardner.
I have the receipt so I could bring it back and get the Glasurit hardner.
Kevin_1990_318iS
Back to Top
steveo View Drop Down
Newbie
Newbie


Joined: 22-December-2002
Location: United Kingdom
Status: Offline
Points: 9
Direct Link To This Post Posted: 09-August-2003 at 10:45
If you are just touching up with a brush then you should be ok with the different hardener but to be on the safe side i would try a test piece first .

steve.
Back to Top
Nigel View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 09-November-2002
Status: Offline
Points: 6941
Direct Link To This Post Posted: 09-August-2003 at 12:03
Steve
Is this the best method of touching up ?
I've always used the touch up sticks with a brush you get from dealers.

Whats in those ?

I have to admit they never seem any good on metallics.
Best Wishes

Nigel

Back to Top
Kevin_E30_318iS View Drop Down
Really Senior Member II
Really Senior Member II
Avatar

Joined: 14-December-2002
Location: Ireland
Status: Offline
Points: 883
Direct Link To This Post Posted: 09-August-2003 at 17:32
The quality of touch-up sticks can vary, but the experience I've had with them is bad, poor colour match, poor adhesion, etc.
By getting some 2-pack mixed you will have the perfect colour match, but there are health & safety issues with 2-pack and it needs to be used with great caution as it contains iso-cyanates and other nasties.
The other downside is that the min you can get mixed is usually 0.25L and the paint and hardner once opened begins to deteriorate and will go off after a couple of years(probably less, but I kept using the stock I had!).
The smallest tin of hardner available in the local paint shops for me is 0.5L, which is alot of waste.
Also not sure about its compatibility with modern water based finishes.
Kevin_1990_318iS
Back to Top
Kevin_E30_318iS View Drop Down
Really Senior Member II
Really Senior Member II
Avatar

Joined: 14-December-2002
Location: Ireland
Status: Offline
Points: 883
Direct Link To This Post Posted: 09-August-2003 at 17:36
Sorry, meant to say thanks Steve in the last post for your helpful advice. I'll give it a try.
Kevin_1990_318iS
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down



This page was generated in 0.234 seconds.