Roddys E36 M-Sport - M52B28 Conversion - Huge Spec |
Post Reply | Page 123 9> |
Author | |
RoddyE36Mtec
Really Senior Member I Stanced Stragh Six! Joined: 28-February-2010 Location: Fife Status: Offline Points: 270 |
Post Options
Thanks(0)
Posted: 12-September-2010 at 22:40 |
Roddy's EURO E36 M-SPORT
How it looks just now AUG 2010! As promised i have started this progress thread of my E36 M-sport
During this progress blog you will see the transformation from - E36 M44 M-Sport to Euro Style E36 M52B28 Engine'd Show Car
Wee bit about the car to explain on the colour first of all,
Genuine Factory 318iS M-Sport (Non sunroof) Rare Titan Silver (Titan silver was not an option on the E36 till 1999 but my car is a 1998 and as i was advised by bmw themself as i had inquired about this, the car was on special order to be that colour before its time by the first owner!) Just wanted to explain that bit before i went any further lol Spec : 1998 (R) 328iS M-Sport ENGINE : Engine Rebuild - Head : S50B30 Head -.080" MLS headgasket -ARP2000 head stud kit -Multi angle valve job -New valve guides -New valves -Resurfaced -Unshrouding of valves -Double valve springs -New hydraulic lifters -RMR Fuel rail -60# injectors Bottum End : M52B28 Block -S50B30 crank -84.5mm Wiseco 8.5:1 pistons (1mm Over bore) -ARP main studs -OEM bearings (std size) -All new gaskets/seals -High performance oil pump -S52B30 style all aluminum oil filter housing -Oil pan has -Tap for oil return line from a turbo Exhuast : Current - -S50B30 M3 Manifold -S50B30 Powerflow decat - Modded to fit 328 -Scorpion Stainless system After Turbo - -Custom Manifold -Custom Exhuast Turbo & Accesories : -Garret GT35R -Turbo Exhaust Manifold -FMIC -Boost Pipes -S54 rad Other Engine Mods : -Fan delete Kit -M20 Lightened flywheel -UUC Underdrive Pulleys -UUC Tranny Mounts/Enforcers -Delrin Carrier Bushes -Clutch Arm Bushes -Z3 Quickshift Interior : -M-Sport Half Leather - Current -M3 Roof Black Non Sunroof Lining - Current -M3 Steering Wheel - Current -M3 Vadar Interior -Custom Retrimed Dash -Custom Retrimed Roof Lining -Custom Retrimed Vadar's -Custom Retrimed Parcel Shelf -Idividual Rear Widnow Blind -Evolution Center Consel (Cup Holders) -Heated Seat Retro Fit -Euro Spec Electric Rear Windows -Ac Schnitzer Carbon Door Panels -Ac Schnitzer Carbon Gear Surround Panel -Ac Schnitzer Carbon Glovebox Blank -Ac Schnitzer Carbon Steering wheel Exterior : Genuine M3 parts from factory : -M3 Front Bumper -M3 Rear Bumper -M3 Sideskirt -M3 Rear Spoiler -M3 Gt Corner spliters -M3 Door Kicks -M3 Bumper Lip -M3 Rear Deffuser Part fitted afterwords - -Ac Schnitzer Carbon Mirrors Type I -Ac Schnitzer Carbon Lip -Ac Schnitzer Carbon Rear Deffuser -Ac Schnitzer Carbon Top Spoiler -Ac Schnitzer Carbon Molding Badges -M3 Gt Class II Rear Wing - Current -M3 Gt Front Adjustable Lip - Not Fitted Lights : -CCFL Angel Eyes -Headlights Tinted -Foglights Tinted -Yellow Inner lights -HID Conversion -M3 Heated Headlight Light Scooshers -Headlight Eyebrows -U.S Spec Parking Lights -PDC Retro Fit Bodywork Mods : -Rolled, Pulled & Flared Arches -Debadged Bootlid -Debadged Bonnet -Bonnet Bra -Carbon fiber Kidney Grills -U.S Spec Number plate blank -M3 Mesh Bumper Grill Suspension/Chassis : -Factory M-Sport Shocks - Current -60mm Lowering Springs - Current -M3 Rear Axle & M3 3.23 Ratio LSD -M3 Front Hubs -M3 Rear Hubs -Eibach Pro Street Coilovers -Eibach Anti Roll Bars -Z3 Rear Shock Mounts Re-inforcement plate -D2 Rear Camber Arms -Camber Adjustable Top Mounts -Cabrio X Brace -Ac Schnitzer Strut Brace Brakes : -318iS Calipers - Current -Brembo 4Pot Front Calipers -Brembo 2pot Rear Calipers -E46 M3 Drilled and Gooved Disks -EBC Red Stuff Pads -E36 M3 Master Cylinder Wheels : -19" Genuine E46 M3 Wheels 8'5" Wide (4 Fronts) - Current -BBS STYLE 5 8" Fronts 9" Rears - Awaiting Fitting Gadgets : -OBC -Heated Seats -Reverse Sensors -Cruise Control -Bmw In Car Phone -Electric Rear Window Conversion In Car Entertainment : Headsup: - Alpine IVA-D310R Screen - Alpine H701 Sound Processor CD / MP3: - Alpine ChaS634 6 Disc CD/MP3 Changer Speakers: - Alpine SPX-137R Speakers - front - Alpine SPX-107R Speakers - rear Subwoofer: - Alpine 15" SWR-1542D Subwoofer - Alpine 15" SWR-1542D Subwoofer Amps: - Alpine MRD-F540 4-Channel Amplifer - Alpine MRD-M1001 Mono Amplifer - Alpine MRD-M1001 Mono Amplifer Controllers: - Alpine RUE-4191 Remote - Alpine RUX-4180 Bass Controller Cables / Accessories: - Inline Voodoo Fuse holder 120 amp Fuse/ LED Read out - Voodoo Splitter LED Readout - 0 Gauge Power and Earth Cables - 4 Gauge Power and Earth Cables - 2 x Dizzy Block (Power/Earth) - KnuKonceptz Triple shield RCA Cables x 3 - Remote Cable - 8 Gauge Speaker Cable - 12 Gauge Speaker Cable Edited by RoddyE36Mtec |
|
Sponsored Links | |
RoddyE36Mtec
Really Senior Member I Stanced Stragh Six! Joined: 28-February-2010 Location: Fife Status: Offline Points: 270 |
Post Options
Thanks(0)
|
Some Pictures Of How The Car Stands At The Moment!!
Comments welcome |
|
RoddyE36Mtec
Really Senior Member I Stanced Stragh Six! Joined: 28-February-2010 Location: Fife Status: Offline Points: 270 |
Post Options
Thanks(0)
|
Here are some pics of the yellow tinting of the inner lights of my headlights.
After fitting these i decided to retint my headlights then do my indicators also. There not as dark as they looks as the light outside started to go once the light have been subjected to heat like my last set did lighting up slightly also! Here is the number plate blank fitted and M3 bumper grill Edited by RoddyE36Mtec |
|
Issy
Admin Group THE BOSS! Joined: 21-February-2007 Location: Port Seton Status: Offline Points: 4429 |
Post Options
Thanks(0)
|
Thanks Roddy this looks interesting. Good luck with the transformation. When do you start it?
Ooops sorry didnt give you a chance to finish posting sorry Edited by Issy |
|
|
|
RoddyE36Mtec
Really Senior Member I Stanced Stragh Six! Joined: 28-February-2010 Location: Fife Status: Offline Points: 270 |
Post Options
Thanks(0)
|
Its fine thats everything for now :)
Main work starts hopefully this week coming.. Engine is not ment to be fitted to the 7th October but i may get it done this week coming of following if there is enough time in the day! Car itself as i keep geting told by my father does not need a respray but there is some small inperfections that are anoying me such as stone chips so car goes for paint soon also, So that is when the major bodywork changes will happin.. But before that my new BBS wheels are going on and my archs are getting rolled and pulled for the to be fitted or the will rub once the coilovers are on with the camber arms. So alot of work happening over the next few weeks and months.. Then last of all the M52 will be getting supercharged :D |
|
Issy
Admin Group THE BOSS! Joined: 21-February-2007 Location: Port Seton Status: Offline Points: 4429 |
Post Options
Thanks(0)
|
Sounds like you are going to be busy!
|
|
|
|
gary
Really Senior Member II Just Call me Wendy ;-) Joined: 16-October-2002 Location: Scotland Status: Offline Points: 4263 |
Post Options
Thanks(0)
|
How long are you giving yourself to get it all done, mate.
|
|
HairyHaggis
Really Senior Member II Joined: 03-March-2008 Location: Glenrothes Status: Offline Points: 800 |
Post Options
Thanks(0)
|
You did a nice job spraying the stairs with the rattle can |
|
BMW E36 328is M52B28 - SOLD BMW E36 318is M44 - SOLD |
|
RoddyE36Mtec
Really Senior Member I Stanced Stragh Six! Joined: 28-February-2010 Location: Fife Status: Offline Points: 270 |
Post Options
Thanks(0)
|
The car will be pritty much ready in the next couple months mate, apart fron interior and supercharger! But apart from that start of next month, Engine Wheels archs will all have been done! |
|
RoddyE36Mtec
Really Senior Member I Stanced Stragh Six! Joined: 28-February-2010 Location: Fife Status: Offline Points: 270 |
Post Options
Thanks(0)
|
Not rattle tins right enough bad just as bad, I dimolished the old stairs in to the house to built a new set and that was as far as i got before i built a fancy set around the existing ones and then the car took main priority so put this protective floor paint on it that they use in garages, was my fathers great idea lolol Trust you to notice that steve haha Edited by RoddyE36Mtec |
|
RoddyE36Mtec
Really Senior Member I Stanced Stragh Six! Joined: 28-February-2010 Location: Fife Status: Offline Points: 270 |
Post Options
Thanks(0)
|
Update : Today my carbon fiber front spliter turned up and it looks amazing : Also today, Myself and my mate Euan who is a painter to trade and also owns a E30 M3, started refurbing my BBS STYLE 5 Wheels down at the lockup : Bolts Removed Wheels Split Being rubed down Ready for refurb The wheels should be ready by wedesnday this week for tyres to be stretched on :D Comment welcome! Edited by RoddyE36Mtec |
|
Issy
Admin Group THE BOSS! Joined: 21-February-2007 Location: Port Seton Status: Offline Points: 4429 |
Post Options
Thanks(0)
|
Wow good job cant wait to see them once they done! Excuse my ignorance ....are you polishing them or painting them?
|
|
|
|
RoddyE36Mtec
Really Senior Member I Stanced Stragh Six! Joined: 28-February-2010 Location: Fife Status: Offline Points: 270 |
Post Options
Thanks(0)
|
Thanks issy :)
They were getting polished but was going to be to much hasel and costly.. So.... Now there geting painted silver metalic on the dish, The metalic in the paint is that small it makes the the paint a shiney bright silver and replicates polished/Dimond cut dish in a way. Its 513 silver or somthing i think And the centers are getting painted Bmw E39 Anthracite grey My mate Euan intraduced me to the 513 silver.. as soon as i went to him about the wheels he had both these colours in mind as he knows what i like and knows im a picky PERSON lol |
|
RoddyE36Mtec
Really Senior Member I Stanced Stragh Six! Joined: 28-February-2010 Location: Fife Status: Offline Points: 270 |
Post Options
Thanks(0)
|
Update : I decided tonight to go out and fit my carbon Ac spliter, So once again front bumper off, Excuse rear wheel i had a blow out :( : And splitter fitted, Please excuse the crap pictures : I will get beter pictures in the light tomorrow! Comments welcome! Edited by RoddyE36Mtec |
|
Cambell
Really Senior Member II Joined: 07-January-2007 Status: Offline Points: 3830 |
Post Options
Thanks(0)
|
Busy boy !!
|
|
RoddyE36Mtec
Really Senior Member I Stanced Stragh Six! Joined: 28-February-2010 Location: Fife Status: Offline Points: 270 |
Post Options
Thanks(0)
|
Yup this is very true!
Today im going to be doing the rest of my wheels if all goes to plan they should be all in primer today. Also orderd some Goodyear Eagal F1's to stretch on to the wheels as the same a good allround tyre for dry and wet conditions. |
|
gary
Really Senior Member II Just Call me Wendy ;-) Joined: 16-October-2002 Location: Scotland Status: Offline Points: 4263 |
Post Options
Thanks(0)
|
Excellent progress mare. You certainly don't hang about. Love the
wheels and splitter |
|
RoddyE36Mtec
Really Senior Member I Stanced Stragh Six! Joined: 28-February-2010 Location: Fife Status: Offline Points: 270 |
Post Options
Thanks(0)
|
Thanks bud..
Yeah this will be the 3rd show car ive built in three years not to mention 106Turbo track car and others so ive became a dab hand at getting things done quikly lol If you want stuff done and done properly do it yourself is what ive always said! |
|
Ham328
Really Senior Member II Straight Six!! Joined: 30-December-2008 Location: The Kingdom of Fife Status: Offline Points: 542 |
Post Options
Thanks(0)
|
Hi Roddy. Your not hanging about with this are you. Style 5s look great on E36s as well. I'll await with interest the end result of the paint on the dishes. Anthracite on the centres wont be a million miles from mine i take it. Darkening the centres is a marmite thing i think. Though mine were done before i bought the car i don't mind it but i think if they're too dark it makes the wheels look smaller Although the engine conversion itself is one i don't really see the point of (purely on the basis that good 328i Sports and M3s go for less than peanuts nowadays) i'll follow your progress with interest. I like a good build thread |
|
Mrs Pontipine is a nosey bint.
|
|
RoddyE36Mtec
Really Senior Member I Stanced Stragh Six! Joined: 28-February-2010 Location: Fife Status: Offline Points: 270 |
Post Options
Thanks(0)
|
Heey fella.. Yeah ive been bashing on each day.. I striped the rest of the Style 5's tonight, a bit at a time is the best way to go about this things ive found. Yeah the anthracite on the wheels is the E39 Colour so it aint to dark so it shall look nice i recon but thats my opinion. Yeah ive found the dont do the Eagals in the size i want to will opt for somthing else after all lolol But as for the engine, ive decided to do it this way as i know ive got a good shell, and its always been well looked after also ive bought the engine paid for it to be fitted for cheaper than you can buy an engine normaly so it has cost me not alot of money and in the end will have a nice car. I will own this for a while once it finnished like ive done preiously with the other cars ive built then move on to somthing beter as a project. OR possibly E46 M3 But thanks for the kind words and hopefully i dont dissapoint with the end result. and hoping catch up with you at one of the up coming meets Ham as i still never got a good look at your car as was dark that night lol. |
|
Post Reply | Page 123 9> |
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |